Protekta
Ceramic Micro Spheres and Silicone Enhanced, Mildew and Algae Preventing, Water Based, Exterior Wall Paint

Product Definition
> Ceramic micro spheres and silicone enhanced, mildew and algae preventing, water impermeable, acrylic emulsion based, long lasting, matt, exterior wall paint.

Application Areas
> On exterior mineral surfaces such as concrete, mortar, cement panel, etc. and on previously painted surfaces.

Features
> Contributes to heat insulation with its ceramic micro spheres
> Water repellent; provides rain to slide away without wetting the wall.
> Prevents mildew and algae growth on walls.
> Water resistant.
> Superior hiding power
> High water vapour permeability, allowing the building to breathe.
> Long lasting, resists to UV rays, rain, heat and frost, thus retains its original properties for years without cracking, blistering and fading.
> Alkali resistant.
> Water thinnable and ecologically compatible
> Solvent free and practically odourless

Technical Features
General Data:
> Composition: Acrylic emulsion based
> Thinner: Water
> Density: Approx. 1.52 gr./cm3
> Colours: White and 144 colours of exterior colour chart. Tintable by Renk Ustası
Application Data:
> Application Temperature Range: 5 - 35° C
> Drying Time: Recoatable after 6 hours and thoroughly dry after 24 hours. Lower temperatures and/or higher relative humidity will lengthen the drying process.
> Consumption: Approx. 0.130 lt./m2 per coat.
> Application: Tools Brush, Roller, Airless spraying equipment
Performance Data:
> Water Vapour Permeability: SD (m) (DIN 52615) Approx. 0.150
> Scrub Resistance: (cycle) (ASTM 2486) > 300
> Gloss: (60°) (ISO 2813) Approx. 3
> Water Absorption: (kg./m2h0,5) (DIN 52617) < 0,100
> Service Temperature: -30° C / +80° C

Application Instructions
> The substrate must be cleaned from dust, dirt, oil and old blistered coatings that may prevent good adhesion. The surface should be made sound, clean and dry. New cementitous substrates must be cured at least 28 days before application.All water insulation precautions should have been taken prior to application.
> Sand glossy and/or solvent based painted surfaces to improve adhesion and remove the occurring powder.
> If necessary, fill the surface cracks and even the substrate with Kalecolor KALIN AKRİLYK MACUN, Kalecolor MACUNART or Kalekim TAMYRART.
> Prime new mineral and old painted surfaces with Kalecolor ÜNY-ASTAR or SYLASTAR and porous and weak mineral surfaces with Kalecolor AKRYLYK ASTAR.
> After thoroughly mixing, thin PROTEKTA with clean water up to a maximum of 10% by volume and apply in two coats by using a brush, roller or spray system.
> Wait for a minimum of 6 hours before applying the final coat.
> Clean the tools with water.
> Ensure that the air and surface temperatures are above +5° C and the surface is rain free during application and 24 hours following the application.
> Do not apply in extremely hot weather, under glaring sun, during strong wind, fog, high relative humidity and imminent rain or frost.
> Dampen the hot surfaces before the application.
> Not suitable for application on horizontal surfaces exposed to rain or moisture.

Warnings
> S2 Keep out of the reach of children.
> S24/25 Avoid contact with skin and eyes.
> S46 If swallowed, seek medical advice.

Storage
> Store between 5 - 35° C.

Packaging
> 2,5 lt., 7,5 lt. and 15 lt. pails.
> 2.5 lt. packages packed together in 4s

Quality Documents
Certificates of Quality: TS 5808

Back

Top

Print