Kalia İpek Mat
Photocathalytic, Mildew and Algae Preventing, Silky Matt, Silicone Enhanced, Water Based Interior Wall Paint

Product Definition
> Acrylic emulsion based, photocathalytic (activated by light), mildew and algae preventing, silicone enhanced, easy to clean, perfectly scrub resistant, silky matt interior wall paint.

Application Areas
> On interiors suitably prepared new mineral surfaces such as concrete, mortar, cement panel, gypsum panel etc. and on old painted surfaces, putty, glass textile and on wallpaper.

Features
> Photocathalytic; by the activation of light it decomposes the harmful materials such as nicotine fume and bad odours transferred by air movements on interior surfaces. Therefore, cleans the air in the room and enables walls to remain clean for a long time.
> Provides relief for those suffering from asthma in particular by preventing algae and mildew growth.
> Easily re-touchable, does not leave brush or roller marks.
> High water vapour permeability, allowing the building to breathe.
> Superior hiding power.
> Solvent free and practically odourless.
> Water thinnable and ecologically compatible

Technical Features
General Data:
> Composition: Acrylic emulsion based
> Thinner: Water
> Density: Approx. 1.35 gr./cm3
> Colours: White and 36 colours of interior colour chart. Tintable by Renk Ustası
Application Data:
> Application Temperature Range: 5 - 35° C
> Drying Time:Recoatable after 6 hours and thoroughly dry after 24 hours.
> Lower temperatures and/or higher relative humidity will lengthen the drying process.
> Consumption: Depending on the evenness and the porosity of the surface approximately
0.090 lt./m2 per coat.
> Application Tools: Brush, Roller, Airless spraying equipment
Performance Data:
> Water Vapour Permeability: - SD (m) (DIN 52615) Approx. 0,250
> Scrub Resistance: (cycle) (ASTM 2486) > 500
> Gloss: (60°) (ISO 2813) Approx. 7
> Service Temperature: -30° C / +80° C

Application Instructions
> The substrate must be cleaned from dust, dirt, oil and old blistered coatings that may prevent good adhesion. The surface should be made sound, clean and dry. New cementitous substrates must be cured at least 28 days before application.
> Before application on old painted mouldy surfaces; clean the surface with a wet cloth and treat with 2 - 3 successive wet-on- wet coats of Kalecolor KÜF TEMİZLEYYCY in order to kill the mould on the wall.
> Sand glossy and/or solvent based painted surfaces to improve adhesion and remove the occurring powder.
> If necessary, fill the surface cracks and even the substrate with Kalecolor YNCE AKRYLYK MACUN or Kalecolor MACUNART.
> To have a fine, silky texture, smoothen the entire surface by using Kalecolor YNCE AKRYLYK MACUN or Kalecolor MACUNART.
> Prime the solvent based painted surfaces or water based painted surfaces on which colour change is desired with Kalecolor GEÇY? ASTARI, old painted water based and very dirty surfaces with Kalecolor SYLASTAR and new and porous surfaces with Kalecolor AKRYLYK ASTAR or Kalecolor SYLASTAR.
> After thoroughly mixing, thin KALYA YPEK MAT with clean water up to a maximum of 25% by volume and apply in two coats by using a brush, roller or spray system.
> Wait for a minimum of 6 hours before applying the final coat
> Clean the tools with water.
> Ensure that the air and surface temperatures are above +5° C during the application and 24 hours following the application.

Warnings
> S2 Keep out of the reach of children.
> S24/25 Avoid contact with skin and eyes.
> S46 If swallowed, seek medical advice

Storage
> Store between 5 - 35° C

Packaging
> 2,5 lt., 7,5 lt. and 15 lt. pails.
> 2.5 lt. packages packed together in 4s

Quality Documents
Certificates of Quality: TS 5808

Back

Top

Print